Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

This tutorial guides you through the process of using CAM Assist's ‘3+2 Axis’ machining mode, with a ‘User-defined' machining direction, to compute a toolpath strategy for a part.

When using the ‘User-defined’ machining direction:

  • The tool orientation comes from the orientation you specify in the Target setup(s) within CAM Assist.

  • A toolpath strategy will only be computed by limiting the tool to the specified orientation.

  • Facing operations will only be computed if the +Z Axis is selected.

  • The tool then operates on the partfrom a fixed orientation, which means that the orientation cannot change during cutting.

This tutorial uses CloudNC’s ‘Demo Part 4'. However, the same process can be used for any part that can be opened in Siemens NX.

Info

CAM Assist works with the Siemens NX manufacturing environment and manufacturing templates.


Preparation

Before following this tutorial, you must have successfully completed the following steps:

  1. Install CAM Assist - follow the instructions in Installing CAM Assist.

  2. Open a part - follow the instructions in Opening a Part (this tutorial uses ‘Demo Part 4’).

  1. Open the ‘CAM Assist’ menu - it contains the CAM Assist ribbon shown in the screenshot to the right.

  2. Click CloudNC CAM Assist - in the CAM Assist ribbon.

image-20240726-100811.png

Using the ‘3+2 Axis’ Machining mode

Panel
panelIconId1f39e
panelIcon:film_frames:
panelIconText🎞️
bgColor#EAE6FF

Video
For an illustration of the content of this tutorial, see the YouTube video Tutorial - 3+2 Axis Machining Mode (User-defined).

On completing the Preparation, you’ll see the CAM Assist user interface with ‘Demo Part 4.prt’ open, as shown below.

image-20240814-100113.png

To use the ‘3+2 Axis’ Machining mode with a ‘User-defined’ machining direction, you’ll take the following steps:


Specify the Machining mode

For Machining mode, CAM Assist provides you with two options: ‘3 Axis’ and ‘3+2 Axis’.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Check the box for 3+2 Axis

image-20240730-111819.png


Specify the Machining direction

For machining direction, CAM Assist providers you with three options: ‘Aligned to X, Y, Z axes’, ‘User-defined’, and ‘Automatic’.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Check the box for User-defined

image-20240730-122326.png


Configuring the Target setups

The content of the ‘Target setups’ section reflects the workpiece configuration of the part, as displayed in the ‘Geometry’ view of the Siemens NX Operation Navigator (as shown below).

Check the Setup(s)

Within CAM Assist, the ‘Target setups’ are numbered sequentially, in the same order as in NX’s Geometry view.

You’ll notice that ‘Demo Part 1’ has two Target setups: ‘Setup 1’ and ‘Setup 2’.

If you want CAM Assist to create a toolpath strategy for a setup, ensure its respective checkbox (Setup 1/Setup 2) is checked.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Checkthe box for Setup 1

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Checkthe box for Setup 2


Same direction for roughing and finishing

The content of the ‘Target setups’ section changes depending on whether ‘Same direction for roughing and finishing' is checked or unchecked.

Info

The side-by-side screenshots below provide an example of the changes to the ‘Target setups’ section.

image-20240807-142041.png

‘Same direction for roughing and checking’ is checked

Checking the box indicates you want the part to be machined using the same direction for both roughing and finishing operations.

image-20240730-115545.png

Note the option for:

  • Select machining directions (0)

This is used to specify the machining direction for roughing and finishing (see below)

‘Same direction for roughing and checking’ is unchecked

Unchecking the box indicates you want the part to be machined using different directions for the roughing and finishing operations.

image-20240730-115625.png

Note the options for:

  • Select roughing directions (0)

  • Select finishing directions (0)

These are used to specify different directions for roughing and finishing (see below).


Specifying a different machining directions for roughing and finishing

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

For Setup 1:

  • Uncheck the box for Same direction for roughing and finishing.

You’ll configure Setup 2 later on in the tutorial.

With the box unchecked, you'll have to specify the roughing direction and the finishing direction separately.

First, the roughing direction…

The ‘Select roughing directions’ icon (see the image to the right) is used to indicate the roughing direction by clicking on the part's face, within Siemens NX, that is perpendicular to that direction.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Click the Select roughing icon

Select roughing directions.drawio.png

Within Siemens NX:

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Click on the face of the model/part that is perpendicular to the direction that will be used for roughing.

Two things happen when you click on a face (as shown in the image to the right):

  1. In Siemens NX - the face is highlighted.

  2. In CAM Assist - ‘Select roughing directions (0) changes to ‘Select roughing directions (1)’.

  3. A green tick is shown to indicate a valid selection has been made.

image-20240812-104803.png

Within CAM Assist:

Next, the finishing direction…

The ‘Select finishing directions’ icon (see the image to the right) is used to indicate the finishing direction by clicking on the part's face, within Siemens NX, that is perpendicular to that direction.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Click the Select finishing directions icon

Select finishing directions.drawio.png
Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Click on the face of the model/part that is perpendicular to the direction that will be used for finishing.

Two things happen when you click on the face (as shown in the image to the right):

  1. In Siemens NX - the face is highlighted.

  2. In CAM Assist - ‘Select finishing directions (0) changes to ‘Select finishing directions (1)’.

  3. A green tick is shown to indicate a valid face has been selected.

Tip

That’s it, you’ve selected a different direction for roughing and finishing.

image-20240812-103028.png
Info

You can click on more than one face.

Keep roughing order

This checkbox is used if you have selected more than one roughing direction:

  • Checked - tool orientations will be ordered in the same sequence as they are selected (only applies to ‘Select roughing directions’, see above)

  • Unchecked - tool orientation will be sequenced by CAM Assist but may not be in the order selected.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

In this tutorial:
Only one roughing directions has been specified for ‘Setup 1’, so it doesn’t matter if ‘Keep roughing order’ is checked or not.

image-20240730-131258.pngImage Added


Specifying the same direction for roughing and finishing

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

For Setup 2:

  • Check the box for Same direction for roughing and finishing.

With the box checked, you'll specify the same direction for roughing and finishing.

The ‘Select finishing directions’ icon (see the image to the right) is used to indicate the roughing direction by clicking on the part's face, within Siemens NX, that is perpendicular to that direction.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Click the Select machining directions icon

user_defined_select_machining_icon.drawio.png

Within Siemens NX:

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Click on the face of the model/part that is perpendicular to the direction that will be used for roughing and finishing.

Two things happen when you click on the face (as shown in the image to the right):

  1. In Siemens NX - the face is highlighted.

  2. In CAM Assist - ‘Select roughing directions (0) changes to ‘Select roughing directions (1)’.

  3. A green tick is shown to indicate a valid face has been selected.

Tip

Job done: you’ve selected a different direction for roughing and finishing.

image-20240812-110630.png
Info

You can click on more than one face.


Set the Avoidance Geometry

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Specifying Avoidance Geometry is an optional step

For details and step-by-step instructions, see the tutorial ‘Using Avoidance Geometry’.

image-20240730-114052.png

Keep roughing order

The checkbox could be:

  • Checked - tool orientations will be ordered in the same sequence as they are selected (this applies to ‘Select roughing directions’, see below).

  • Unchecked - tool orientation will be sequenced by CAM Assist but may not be in the order selected.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

For ‘Setup 1’ and ‘Setup 2’

Check the box for Keep roughing order icon

image-20240730-131258.png

Set the Workholding security

CAM Assist will choose roughing tools suitable for the specified workholding.

Set the slider to the required position between the two extremes:

  • Excellent - a more secure ('excellent') workholding, such as a vise with serrated jaws, will result in CAM Assist selecting larger tools or more aggressive cutting parameters. This will result in faster toolpaths, but with more force on the workpiece.

  • Poor - a less secure ('poor') workholding, such as a thin part held by a soft jaw, will result in CAM Assist selecting smaller tools or less aggressive cutting parameters. This will produce slower toolpaths, but with less force on the workpiece.

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

For ‘Setup 1’ and ‘Setup 2’

Set the Workholding security slider to 'Excellent’.

image-20240730-131405.png

Examining CAM Assist’s other tabs

Before clicking OK, it’s a good idea to examine the other tabs to ensure that the requirements for CAM Assist’s tool strategy are fully configured:

Panel
panelIconId1f449-1f3fd
panelIcon:point_right::skin-tone-4:
panelIconText👉🏽
bgColor#F4F5F7

Click OK.

On clicking OK, CAM Assist closes and computes a toolpath strategy, which is displayed within the ‘Program Order View' of Siemens NX’s Operation Navigator (as illustrated in the following screenshot).

image-20240812-113544.png